020 8539 4707

THE ECO-STORE THAT SAVES YOU MORE

Ultrotherm 10KG Insulation Adhesive

Ultrotherm Adhesive - 15KG

Ultrotherm adhesive. Used for bonding Ultrotherm tiles and Ultrotherm reveal tiles. Supplied in a 15kg tub (covers up to 10m 2 or 20 Ultrotherm tiles).

Please note, this product is only shipped once a week. Read More

Please see below for more information or contact us

£94.80 inc VAT

£79.00 ex VAT
In stock

All prices include VAT where applicable

Estimate delivery cost
  • Description
  • Technicals
  • Downloads
  • Installation
  • Q & A
  • How it does the job
  • Delivery and Returns

Ultrotherm adhesive. Used for bonding Ultrotherm tiles and Ultrotherm reveal tiles. Supplied in a 15kg tub (covers up to 10m 2 or 20 Ultrotherm tiles). 

Please note, this product is only shipped once a week.  

To download a technical data sheet with more information, click here.

Ultrotherm adhesive. Used for bonding Ultrotherm tiles and Ultrotherm reveal tiles.

Supplied in a 10kg tub (covers up to 10m 2 or 20 Ultrotherm tiles).

 


Thermal Resistance

 

Improvement in thermal resistance of a solid 9” brick wall achieved by installing Ultrotherm
Thermal resistance of Ultrotherm with plaster skim 0.307 m2 K/W

Resistance of un-insulated 9” solid brick wall

0.476 m2 K/W

Resistance with Ultrotherm (excluding adhesive)

0.783 m2 K/W

‘U’ value of un-insulated 9” solid brick wall

2.1 W/m2 K

‘U’ value of 9” solid brick wall with Ultrotherm

1.2 W/m2 K

Expected service life

25 Years
Typical % improvement in ‘U’ value 40%

 

 

Fire Resistance


Ultrotherm has a ‘Class 0’ fire rating in accordance with Building Regulation Approved Document B.


Testing classification based on:

BS 476: Part 6 1989 + A1:2009 (Fire propagation)
BS 476: Part 7 (Surface spread of flame)


The polyurethane foam used in the manufacture of Ultrotherm also meets the following British Standards:

BS 5852 Ignition source crib 7
BS 6853 Annex B.2 Toxic fume
BS 853 Smoke density (3 metre cube test).

 

 

Cost Savings

  Fuel Cost Savings (£ p.a.)
Property Type Bedrooms Gas Electricity

End Terrace House

2 136 444

Semi-Detached House

3 115 376

Detached House

4 414 1350

 

 

 

Fuel Costs (p/kWh)
Electricity

0.58982

Gas

0.20435

 

 

Installation

Below is a video guide on how to install ultrotherm tiles.

 

Below is a video of how to plaster over the endotherm tiles once installed.

 

Below is a video showing you how to reinstate everything you took out of your room.

IDTJ.com Ultrotherm Products - Technical Information (20141120_IDTJ_Ultrotherm_Technical_Information_1.pdf, 176 Kb) [Download]

Our products and solutions are no different from any other appliance buy or home/ office improvement you make.

To help makes things easier for you, we've given a guideline on the approximate skill-level and time involved in the installation of this product:

DIY: 1-2 Days

Professional: 1 Day

Please note: some of you might think you're handier than you are! This is a guideline only, intended only to help you understand how simple installation is and whom you could ask to do it for you. If you were unsure, we would recommend getting the professionals in!

 

Installation Guide

For more information on installing Ultrotherm, please see the following:

 

Video Guides

The following are the video guides that show you how to install Ultrotherm:

 

Installing Ultrotherm Tiles

 

Plastering Ultrotherm

 

Reinstatement Stage

 

Step-By-Step Guide

 

Step 1: Preperation

repare wall surfaces by removing wallpaper or flaky paint. PVA adhesive can be used if necessary to stabilise the surface of the wall. Ultrotherm® can be installed with or without removing skirting boards and coving. Radiators should be lifted from their brackets but the brackets themselves do not need to be removed.

 

Step 2: Installing Ultrotherm® Tiles

Apply Ultrotherm® adhesive to the wall surface directly from the container using a 6mm notched trowel. Once sufficient adhesive has been applied, an Ultrotherm® tile is pressed firmly on to the wall. Apply further adhesive and tiles until the wall is completely insulated. Ultrotherm® tiles should be cut around radiator brackets. These can be covered with removable strips of Ultrotherm® once the wall has been plastered. Ultrotherm® is easily cut using decorator’s scissors.

 

Step 3: Installing Ultrotherm® Without Removing Skirting Boards and Coving

A 15mm plastic trim bead is bonded to the plaster above the skirting board and beneath the coving using Ultrotherm® detail adhesive. The insulation tiles are then located tightly into the trim bead and pressed firmly into the wall adhesive.

 

Step 4: Installing Ultrotherm® Insulated Trim Beads and Reveal Tiles

Ultrotherm® insulation beads are installed with the insulation strip in contact with the window or door frame using Ultrotherm® detail adhesive. Ultrotherm® adhesive is applied to the window or door reveal using a 6mm notched trowel. Ultotherm® reveal tiles should be cut to the required size, located tightly into the insulated trim beads and pressed firmly into the wall adhesive.

 

Step 5: Plastering Ultrotherm®

The joints between the Ultrotherm® tiles must be covered with fibre mesh tape.
Ultrotherm® angle beads are used to form external angles. In most cases Ultrotherm® is plastered using Thistle Board finish or Multi-finish. The first step is to apply a base coat of plaster that fills-in the circular holes behind the mesh covering. The plaster should be mixed to a thicker consistency than normal for this coat. It is also possible to build-up layers of plaster in a more traditional style. Applying a coat of ‘Hardwall’ plaster before the skim coat increases impact resistance. Once the filling coat has started to set, two further coats of plaster skim are applied to the wall.

 

Step 6: Re-instatement Stage

reinstated. Care should be taken not to over-compress Ultrotherm® when securing skirting boards or other items back to the wall. Before re-hanging radiators, Ultrotherm® should be placed over the brackets to prevent cold spots. This also allows the radiator brackets to be easily removed if necessary. Walls can be decorated after approximately two weeks or once the plaster has fully dried.

 

Pdf Guide


To download a pdf guide of the above step-by-step installation instructions, click here.

Nobody's asked us any questions yet, to be the first by contacting us.

Here are just some of the ways it does the job:

Economic:

  • Reduces energy bills as you need to pump less heat into the room.

Better Consumption:

  • Can reduce heat loss through by up to 40%.

Feel good:

  • No need to alter the aesthetics of you room.

Simple:

  • Easy to install: as simple to put up as wallpaper;
  • Plastered using traditional skill avoiding the hassle of other insulations;
  • Can be cut to fit around the windows, coving, radiators etc… in your room;
  • Bends around awkward shapes.

 Reliable:

  • Class 0 fire rating.

Delivery

Here is a guide to delivery and returns.  We are constantly looking to minimise delivery costs so some products may vary.  All available delivery options will be shown in the basket and correct delivery will be calculated before you check out.  You will only be charged one delivery cost.   

Not all options available for all products.

To calculate accurate delivery cost to any address, please click ‘Estimate delivery cost’ above.  

International deliveries: Please call us for more information on international deliveries

Collection from ItDoesTheJob.com HQ available for some products. 


Returns
We think you’ll be more than happy with your purchase.  If you’re not, simply return to us within 30 days.  
 

Read more about Delivery and Returns